ELS V8 Question

[Rareroblox 30]

Hi, when I have ELS V8 and I want to change the light pattern on the control menu thing. how do I change it to like C-05 like that. I dont want E-01 anymore, it is too boring for me. How do I change it? I found a picture of what I mean:

 

[davelaric 69]

Open the control panel, keys are U,I, and O. 

[SteelMods 6]

What davelaric said. U is for primary lights, I is for secondary lights (such as a traffic advisor) and O are for wig-wags.

[Rareroblox 30]

What davelaric said. U is for primary lights, I is for secondary lights (such as a traffic advisor) and O are for wig-wags.

I know that but it wont go to c it just stays like at E-12 and it is finished it goes back down to E-00 and keeps saying at E

[MrNord 10]

Check your ELS.ini and your VCF file(vehicle config. file) for that specific vehicle(s). It could be caused by some options, parameters and such...

[Rareroblox 30]

Check your ELS.ini and your VCF file(vehicle config. file) for that specific vehicle(s). It could be caused by some options, parameters and such...

all of the vehicles have that like police1, 2, firetruk, ambulance etc.

[SuperStumpje 667]

E, C an whatever else there is can be changed by changing "leds" in the vehicle config intowhatever you want. The options and corresponding letters are somewhere in the manual.

Edited July 4, 2014 by SuperStumpje

[Rareroblox 30]

E, C an whatever else there is can be changed by changing "leds" in the vehicle config intowhatever you want. The options and corresponding letters are somewhere in the manual.

Can you show me a tutorial?

[iiKonrad 240]

Also, since this hasn't been mentioned you can press Alt + U to go backwards in the primary light pattern, same for all the modes. In case you want like lightstage 10, and you accidently go to 11, just do Alt + U.

[Rareroblox 30]

Also, since this hasn't been mentioned you can press Alt + U to go backwards in the primary light pattern, same for all the modes. In case you want like lightstage 10, and you accidently go to 11, just do Alt + U.

I know all of that stuff, it is just I need to know how do I go into the C part of the control panel. whenever I hit alt + U to go back and I hit alt + u when I am on E-00 it goes to E-12 and then back, and back. but never reaches C pattern.

[XL20014 2]

If I'm not mistaken, I think the "C-00" pattern ID is reserved for either "rota" or "strb". Unless you change the secondaries in the config file, you won't be able to switch over to C in-game.

[Uhnother Gamer 47]

I know all of that stuff, it is just I need to know how do I go into the C part of the control panel. whenever I hit alt + U to go back and I hit alt + u when I am on E-00 it goes to E-12 and then back, and back. but never reaches C pattern.

 

Go to GTA IV Directory. (Where ELS is)

Open the ELS FOLDER.

Select the configuration file for the car you want to change the pattern for.

Open it and scroll down, you will see:

 

These are your wigwags.

[ WRNL ]

Type = tkdn

UseScnNotTkd = off

ForcePatForLstg = on

PatId_Lstg3 = 8                           .

 

These are your Primary Lights

[ PRML ]

Type = leds

ForcePatForLstg = on

PatId_Lstg2 = 77                          <-----To change what pattern will show when Lightstage 2 is on

PatId_Lstg3 = 90                           <-----To change what pattern will show when Lightstage 3 is on

Lstg2ActiveExtras = 2and3

ExpressModeRandPat = off

ForcePatForSrnTones = on

PatId_Yelp = 0

PatId_Alt1 = 0

PatId_Alt2 = 0

 

These are your Secondary Lights, or Sectional Lights. Usually these are Yellow (amber) color, on the back of the police car, usually in the back window, or on the back of the main Primary Lightbar

[ SECL ]

Type = leds

DisableAtLstg3 = on

ForcePatForLstg = off

PatId_Lstg1 = 2                         <---Shows what pttern will show for lightstage 1  

PatId_Lstg2 = 0                        <---Shows what pttern will show for lightstage 2

PatId_Lstg3 = 0                    <---Shows what pttern will show for lightstage 3

 

Hope that helped.

[southaussiemate 44]

I assume you are used to ELS version 6 where the primary patterns change the letter after every few patterns. ELSv7 and v8 just use one letter for each lighting type.

for example...

 

E-00 to E-96 is for any LED patterns. this contains every pattern in the old ELSv6 layout and many many more.

S-00 to S-whatever is for any strobes patterns. (change from "leds" to "strb" in the config file)

R-00 to R-05 is for any ELS-H patterns (this it for "rota" in the config)

 

secondaries are the same but there is also M-00 and C-00.

C is for directional patterns ("drct" in the config)- these are your normal ELSv6 styled patterns

M is for marquee or message board options. ("marq" in the config)

 

Hope this helps a little.

[Uhnother Gamer 47]

I assume you are used to ELS version 6 where the primary patterns change the letter after every few patterns. ELSv7 and v8 just use one letter for each lighting type.

for example...

 

E-00 to E-96 is for any LED patterns. this contains every pattern in the old ELSv6 layout and many many more.

S-00 to S-whatever is for any strobes patterns. (change from "leds" to "strb" in the config file)

R-00 to R-05 is for any ELS-H patterns (this it for "rota" in the config)

 

secondaries are the same but there is also M-00 and C-00.

C is for directional patterns ("drct" in the config)- these are your normal ELSv6 styled patterns

M is for marquee or message board options. ("marq" in the config)

 

Hope this helps a little.

 

He doesn't want the letters to change he wants the patterns to change.

ELS6 is old. It doesn't have any "extra" lights.

What i showed above explains how to change the light patters for each lightstage and section for ELSv8.

Any older version, whether it be LCPDFR, ELS, or any mod/script, people aren't going to give support for. They are going to want support for the most updated version of whatever.

If he gets ELS6 and ends up needing help, almost anyone who replies will tell him to just get ELSv8.

 

[southaussiemate 44]

I was referring to how ELSv6 cycles through patterns, starting with A-00 to A-07 then B-00 to B07 then C-00 and so on. The origional post looked to me like he/she was wondering why it was stuck on "E" and not changing through the letters like that.

[Uhnother Gamer 47]

I was referring to how ELSv6 cycles through patterns, starting with A-00 to A-07 then B-00 to B07 then C-00 and so on. The origional post looked to me like he/she was wondering why it was stuck on "E" and not changing through the letters like that.

 

Well if all he wants is the letters to change then he can download v6 all he wants lol.

[Mustu 230]

I think if it's going back to zero, you should replace the default_config file and the SLOTCONTROL_ file as well. I assume you're using a clan's (which you don't want), so simply overwrite the default_config and SLOTCONTROL, using the ones that came with ELS. Also, I suggest reading the readme. That is the best place to find all of this, trust me.

[Coast Side Kyle 7]

On 7/4/2014 at 2:01 PM, davelaric said:

Open the control panel, keys are U,I, and O. 

These controls do not work for me even though els works just fine except for these keys to open the menus like my j,k, and l and my sirens and everything work just fine and I have it setup just like everyone else unless you have to change something in one of the ini files

Edited January 17, 2017 by Tech3xpert

[CouthInk4 1,285]

14 hours ago, Tech3xpert said:

These controls do not work for me even though els works just fine except for these keys to open the menus like my j,k, and l and my sirens and everything work just fine and I have it setup just like everyone else unless you have to change something in one of the ini files

 

Please don't comment in topics that have been inactive for 30+ days, it's against our Community Guidelines to do so. Please create your own topic regarding this. Locking to prevent further replies