Jump to content

W.I.P Tahoe

Posted Image

W.I.P

(having some handling issue)

From the album:

gta iv

  • 236 images
  • 0 comments
  • 702 image comments

Photo Information for W.I.P Tahoe


Recommended Comments

Needs more photos, because from this angle it looks like the Fog Lights on the ram bar are just floating. Also, it looks like someone smashed in the passenger side of the truck with a bat or something, its not a normal smooth flowing side panel. I'm not sure if this was done intentionally to reduce poly-count but it looks a bit goofy to me.

Share this comment


Link to comment

This tahoe is not looking very good and isn't up to it's full potential. Some suggestions:

1) Make it so the fog lights aren't floating there.

2) Make it look like a police car, and not like a POV with a ram bar and light bar. - This can be accomplished by adding an MDC a partition and possibly replacing the leather luxurious seats in the rear with something else, also a dash cam system would be nice too. 

 

(Personal note- I don't think an older light bar like the current one, looks good on a newer vehicle like the tahoe)

 

                                                                                                                                                                                                                                                                                                                   

Share this comment


Link to comment

This tahoe is not looking very good and isn't up to it's full potential. Some suggestions:

1) Make it so the fog lights aren't floating there.

2) Make it look like a police car, and not like a POV with a ram bar and light bar. - This can be accomplished by adding an MDC a partition and possibly replacing the leather luxurious seats in the rear with something else, also a dash cam system would be nice too. 

 

(Personal note- I don't think an older light bar like the current one, looks good on a newer vehicle like the tahoe)

You know that Code 3 still makes those lightbars, right?

Share this comment


Link to comment

Needs more photos, because from this angle it looks like the Fog Lights on the ram bar are just floating. Also, it looks like someone smashed in the passenger side of the truck with a bat or something, its not a normal smooth flowing side panel. I'm not sure if this was done intentionally to reduce poly-count but it looks a bit goofy to me.

the texture of the housing darker then the ram bar so this is why it may looks floating above the ram bar http://imageshack.us/photo/my-images/22/t29y.jpg/

about the passenger side it looks fine to me and it is bxbug's model i didn't edit the model at all.

thanks for the feedback .  

Share this comment


Link to comment

This tahoe is not looking very good and isn't up to it's full potential. Some suggestions:

1) Make it so the fog lights aren't floating there.

2) Make it look like a police car, and not like a POV with a ram bar and light bar. - This can be accomplished by adding an MDC a partition and possibly replacing the leather luxurious seats in the rear with something else, also a dash cam system would be nice too. 

 

(Personal note- I don't think an older light bar like the current one, looks good on a newer vehicle like the tahoe)

your suggestions are welcome but i assembled this car for my personal use .

Share this comment


Link to comment

This car needs to be a PPV (Police Patrol Vehicle); which means you need a lot of editing for example, removing badges that say 'Tahoe', moving the wheels higher so that the car sits lower, remove the fog lights, add some minor stuff to the windows. Check out my OSHP Tahoe on lcpdmods for a reference. Also Tahoes do not use that PB-200 variant, they use stuff more like a PB-450L for example. I wish you luck!

Share this comment


Link to comment

This car needs to be a PPV (Police Patrol Vehicle); which means you need a lot of editing for example, removing badges that say 'Tahoe', moving the wheels higher so that the car sits lower, remove the fog lights, add some minor stuff to the windows. Check out my OSHP Tahoe on lcpdmods for a reference. Also Tahoes do not use that PB-200 variant, they use stuff more like a PB-450L for example. I wish you luck!

thanks for the advise man , i appreciate it. 

Share this comment


Link to comment

I will add proper interior textures if you want once you're done. Btw I like it except the fog lights look like an odd positioning cos if you ram you would brake them?

Share this comment


Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×